Abstract
With the development of modern industrialization, low-carbon industry has become an inevitable trend. In various industrial fields, high-efficiency and energy-saving heat exchangers have been developed to replace traditional heat exchange equipment. However, improving the performance of heat exchangers alone cannot achieve the optimal energy-saving effect for the entire production system.
Based on actual operating conditions in the petrochemical industry, this paper reviews the application environments of different types of heat exchangers, the development of energy-saving technologies, as well as research progress in fouling removal and fault treatment. New research directions are also proposed.
A heat exchanger, also known as a thermal exchanger, is a device mainly used to achieve heat transfer between different fluids. During petrochemical production, process media often need to be heated or cooled. According to different operating conditions and production requirements, various types of heat exchangers can be selected to ensure that process fluids reach the required temperature levels and meet the requirements of chemical reaction processes.
Due to its operating principles and functions, heat exchangers play an important role throughout the entire refining process. They are key equipment for ensuring proper temperature control of process fluids, maintaining stable operation of refining systems, and recovering waste heat for energy conservation. In addition, because heat exchange equipment is widely used in the petrochemical industry, it represents a significant proportion of equipment investment costs. The related energy consumption and metal losses are also major factors requiring attention.
1. Application Progress of Heat Exchangers in the Petrochemical Industry
1.1 Application of Heat Pipe Heat Exchangers in Waste Heat Recovery
Heat pipe heat exchangers have been successfully applied in harsh waste heat recovery conditions in the petroleum industry, especially in processes involving high-sulfur fuels.
In petrochemical production processes, high-temperature heating and cracking equipment are essential. For example, in the production of light olefins, high-temperature petroleum naphtha cracking furnaces are commonly used. The exhaust gas temperature from these furnaces can reach 200–400°C. Due to the severe operating environment, the generated waste gas cannot be directly discharged into the atmosphere.
Air preheating heat pipe heat exchangers can utilize the residual heat from exhaust gases to preheat combustion air, improving energy efficiency while reducing environmental pollution.
In recent years, various combinations of tubular heat exchangers have been widely adopted both domestically and internationally to achieve better energy-saving and waste heat recovery performance. The main production process is shown in Figure 1.
1.2 Application of Helical Baffle Heat Exchangers in Cooling and Heat Exchange Processes
The helical baffle heat exchanger is a new type of high-efficiency heat exchange equipment. Its concept originated from the spiral plate heat exchanger structure proposed by Sweden's Rosenbland company in 1930, which was subsequently patented. Later, countries including the United Kingdom, the United States, Germany, and the former Soviet Union developed and manufactured similar equipment.
China began introducing and applying this technology in the chemical industry during the 1950s. By the mid-1960s, domestic manufacturers had achieved mass production through rolling processes. In 1973, China compiled the Selection Manual for Spiral Plate Heat Exchanger Drawings. The latest standard, JB/T4751 Spiral Plate Heat Exchanger (2003 edition), represents the development level of spiral plate heat exchanger technology in China.
Compared with traditional heat exchangers, spiral plate heat exchangers have advantages including higher heat transfer coefficients and self-cleaning capability caused by fluid turbulence, which helps prevent sediment accumulation.
Therefore, in the petrochemical industry, spiral plate heat exchangers are mainly used for heating and cooling processes involving gasoline, diesel fuel, ammonia water, chlorine water, brine, strong acids, strong alkalis, and nitrogen-hydrogen-ammonia mixed gases.
They are also widely applied in heating, cooling, condensation, and reboiling systems for alcohols, resins, urea, small molecular monomers, polymerized olefins, and related intermediate products.
Hao Zhenliang et al. experimentally studied the relationship between shell-side pressure drop and flow rate, the variation of shell-side convective heat transfer performance with Reynolds number (Re) and Nusselt number (Nu), and the shell-side heat transfer coefficient under unit pressure drop conditions for helical baffle and segmental baffle heat exchangers.
Their research provided guidance for equipment selection under different operating conditions. The main conclusions are as follows:
(1) Under the same Reynolds number conditions, the shell-side convective heat transfer coefficient of segmental baffle heat exchangers is higher than that of helical baffle heat exchangers.
(2) Under the same shell diameter and flow rate conditions, the shell-side pressure drop of helical baffle heat exchangers is negatively correlated with the helical angle. However, regardless of the selected helical angle, the pressure drop remains lower than that of segmental baffle heat exchangers.
(3) Different from the above two conclusions, when considering heat transfer performance per unit pressure drop, the shell-side convective heat transfer coefficient of helical baffle heat exchangers is higher. When the helical angle is approximately 40°, the convective heat transfer coefficient reaches its maximum value, resulting in the highest overall heat transfer performance.
1.3 Energy-Saving Application of High-Efficiency Plate Heat Exchangers in Oil Refining
In medium and large-scale oil refineries, there can be approximately 400 heat exchangers of various types. These systems often operate under high pressure and high temperature conditions. Internationally, shell-and-tube heat exchangers have reached operating levels of 8.4 MPa pressure and 1500°C temperature, with heat transfer areas reaching up to 6,700 m².
Due to the high construction costs of offshore oil platforms, welded plate heat exchangers have been widely used in offshore oil production because of their compact structure, lightweight design, excellent heat transfer performance, and lower cost.
Their main applications include cooling mechanical lubricating oil and freshwater (such as engine jacket cooling water). In oil fields, they can also be used for crude oil heating and other processes.
The main challenge lies in the design and calculation of process systems. In actual production, energy losses are often caused by unreasonable process design.
Chen Jianwei et al. conducted theoretical research on the pressure drop calculation of cooling plate heat exchangers used in petrochemical applications. Based on the characteristics of heat exchangers and heat transfer principles, they assumed that the liquid phase along the flow channel increases linearly and established relationships between flow channel length, actual mass vapor quality, and volumetric vapor quality. The calculation results were consistent with practical operating data.
The main conclusions are as follows:
(1) Under phase-change conditions, when calculating fluid pressure drop, the fluid should be considered as a two-phase or multiphase flow. Single-phase flow or homogeneous flow models should not be used as substitutes for multiphase flow calculations. A separated flow model should be applied.
(2) During cooling processes in the petrochemical industry, partial condensation may occur, resulting in the formation of liquid films on heat transfer surfaces. Therefore, when selecting compact heat exchangers such as plate-fin heat exchangers, achieving a reasonable and economical design requires consideration of structural parameters. Simply increasing heat transfer area and adding safety margins is not sufficient.
1.4 Application of Thin Film Evaporators in Concentration and Drying Processes
Thin film evaporators are commonly used in petrochemical processes such as caustic soda concentration, sodium sulfide evaporation, resin drying, and rubber drying. They provide significant economic benefits.
Compared with traditional equipment such as cast iron evaporation pans, thin film evaporative heat exchangers heated by thermal oil furnaces have the following advantages:
(1) The equipment footprint can be reduced by nearly 6%. The process enables mechanized evaporation, simplifies operation, and converts intermittent production into continuous production, thereby improving industrial efficiency.
(2) Driven by the rotating scraper, the heat transfer performance is significantly improved. The evaporation time on the surface can be reduced to less than one minute, reducing scaling and carbon deposition. The product is less likely to decompose and is suitable for heat-sensitive materials. At the same time, sediment formation is reduced, resulting in easier maintenance and cleaning.
(3) Compared with cast iron evaporation pans, the supporting thermal oil furnace can reduce coal consumption by approximately 50%. It can operate at temperatures up to 300°C while maintaining safe operation under non-pressurized conditions.
(4) The equipment is convenient for process scale-up design and can replace traditional kettle-type dryers. During large-scale production expansion, the deviation caused by scaling up is relatively small.
However, some technical challenges still exist in practical applications.
For example, scraper grooves are usually made of polytetrafluoroethylene (PTFE), which has excellent corrosion resistance but limited high-temperature resistance. One possible solution is to use materials such as graphite that provide both corrosion resistance and high-temperature resistance (>280°C).
Process pipelines are usually made of seamless pipes, which may require replacement approximately every 30 days. A possible improvement is to use stainless steel pipes or pipes with corrosion-resistant internal linings, such as fluoroplastic-lined heat exchanger tubes.
In addition, corrosion problems associated with circulation pumps also require further solutions.
2. Fouling Removal and Countermeasures for Heat Exchange Equipment in the Petrochemical Industry
According to Steinhagen et al., a survey of 3,000 different types of heat exchangers in New Zealand showed that more than 90% of heat exchangers experienced fouling problems. A comparison of fouling conditions among different types of heat exchangers is shown in Figure 2.
Domestic and international studies indicate that the annual cost associated with fouling treatment in the petroleum refining and chemical industries reaches approximately 15.6 million, resulting in significant economic losses and resource consumption.
Under actual operating conditions in the petrochemical industry, the formation mechanisms and classifications of fouling can mainly be divided into the following categories:
Corrosion fouling models
Solidification fouling models
Surface material-induced fouling models
Gas-phase fouling models
Chemical reaction fouling models
During practical operation prediction and analysis, fouling can be classified according to these mechanisms. By selecting appropriate heat exchanger types according to different operating conditions and calculating optimal cleaning intervals, economic losses can be reduced.
Furthermore, considering the high-temperature and high-pressure operating environments in petrochemical applications, the main treatment methods include:
Heat transfer enhancement
Mechanical cleaning methods
Chemical cleaning methods
Online monitoring and real-time cleaning technologies
3. Failure Analysis and Maintenance of Heat Exchangers in the Petrochemical Industry
3.1 Prevention of Corrosion and Wear in Heat Exchangers
During the operation of heat exchangers in the petrochemical industry, corrosion leakage accidents frequently occur. These failures can interrupt stable production and are considered one of the major equipment problems in petrochemical systems.
Such leakage problems are mainly classified into erosion leakage and corrosion leakage. Current solutions mainly focus on repairing damaged equipment after failures occur, improving production processes to prevent failures, and reducing equipment degradation through proper selection of heat exchanger materials and types.
3.1.1 Causes of Corrosion and Wear in Heat Exchangers
Analysis from the perspective of raw materials
The raw materials used in petrochemical production, especially crude oil, contain complex chemical components. In addition, crude oil generally has high viscosity and contains solid particles of irregular sizes.
As a result, the working medium in contact with heat exchanger surfaces is highly complex. The equipment is often subjected to both mechanical damage caused by physical friction and severe chemical corrosion.
Analysis from the perspective of chemical processes
The entire petrochemical production chain often involves high-temperature (>1000°C) and high-pressure operating conditions. Various forms of corrosion may occur simultaneously and interact with each other.
For example, the high flow velocity required during production processes is a direct cause of erosion corrosion, while also accelerating existing corrosion leakage problems.
Therefore, in heat exchanger failures, leakage and corrosion are usually closely related and can create a synergistic effect that accelerates equipment deterioration.
3.1.2 Classification of Heat Exchanger Corrosion and Wear and Countermeasures in the Petrochemical Industry
(1) Surface corrosion and wear of heat exchangers
Surface corrosion is the most common cause of heat exchanger tube leakage, accounting for approximately 90% of cases.
The process media used in petrochemical production often have certain levels of viscosity and adhesion. High-speed fluids containing solid particles and bubbles continuously impact heat transfer surfaces, generating local surface pressures of up to 10 MPa, which may cause fatigue erosion and metal surface damage.
Therefore, process requirements often specify that the medium flow velocity should be greater than 2 m/s.
(2) Electrochemical corrosion caused by surface deposits
During petroleum refining processes, process media usually have high viscosity and may experience solidification under certain conditions. This can cause materials to accumulate on heat exchanger surfaces and form deposits.
The unstable, discontinuous, and uneven characteristics of these deposits can lead to cracks and gaps. Differences in oxygen concentration between the inside and outside of these gaps may trigger electrochemical corrosion.
The related corrosion reactions mainly include:
Metal dissolution reactions, namely anodic oxidation;
Cathodic reduction reactions;
Progressive expansion of corrosion caused by electrochemical imbalance.
(3) Corrosion on the water side surface of heat exchanger tubes
In heat exchange systems, water is frequently used as the heat transfer medium, making water-side corrosion a common issue.
The main corrosion mechanisms include:
Reduction of pH value;
Water vapor penetration;
Attack caused by dissolved oxygen;
Chloride ion (Cl⁻) corrosion;
Sulfide ion (S²⁻) corrosion.
These reactions can generally be divided into chemical corrosion and electrochemical corrosion.
The requirements for corrosion-resistant materials on the water side of heat exchanger tubes include:
Good thermal conductivity and strong surface adhesion;
Excellent resistance to temperature variations and sufficient hardness;
Strong resistance to ion corrosion;
Good anti-scaling performance;
Excellent resistance to water vapor penetration.
3.1.3 Corrosion Protection Methods for Heat Exchangers
Currently, corrosion protection methods for heat exchangers in the petrochemical industry mainly include:
(1) Sacrificial anode protection
This method protects heat exchanger materials by using a more active metal as a sacrificial anode to prevent corrosion of the main equipment.
(2) Development and application of anti-corrosion coatings
Anti-corrosion coatings are widely used in heat exchanger protection. By applying an extremely thin metal coating or inorganic coating on the contact surface, harmful substances and fouling deposits can be effectively isolated.
A commonly used coating is the CH-784 epoxy amino anti-corrosion coating system.
(3) Improvement of heat exchanger materials
To prevent corrosion caused by water quality and aggressive media, improved materials can be selected.
Heat exchangers made of stainless steel, copper alloys, and titanium alloys generally provide excellent corrosion resistance. However, their higher material costs limit their application in some industries.
3.2 Welding Technology for Heat Exchanger Flange Crack Repair
At present, cold fusion welding repair technology is widely used for industrial field maintenance.
Cold fusion welding technology is a new repair technology developed based on gas-shielded welding techniques. It is frequently applied in the repair and maintenance of damaged heat exchangers in the petrochemical industry.
Its main characteristics include:
(1) Low heat input and short welding time
The heat generated during welding is extremely low. The welding process only takes several tens of milliseconds, avoiding problems such as annealing discoloration.
(2) Small welding pool and excellent repair quality
The welding pool volume is less than 2 mm³. The stress distribution is dispersed, reducing concentrated stress on the repaired component.
The process does not cause cracking or deformation. In addition, inert gas protection prevents the formation of pores and bubbles, resulting in a smooth and clean repaired surface.
(3) Compact equipment and suitability for on-site repair
The welding equipment is small and suitable for real-time field repair.
A wide range of welding wires can be selected, allowing repair of heat exchangers made from different materials.
4. Future Development Outlook
It is worth noting that different process requirements require different types of heat exchangers. In addition, the parallel or series arrangement of heat exchangers has a significant impact on the operating performance of the entire process system.
The selection and matching of components are also critical factors. Reliability-oriented design requires that components have sufficient adaptability to withstand various operating conditions, random load changes, and stress variations commonly encountered in the petrochemical industry. This design concept provides improvements over the limitations of conventional design methods.
In terms of energy conservation and emission reduction, future development should not only focus on improving heat exchanger structures but also pay more attention to the development of advanced heat exchanger materials.
Among these research areas, heat exchanger surface coating technology has significant potential. The future direction of coating development includes:
Lightweight design;
High-temperature and high-pressure resistance;
Excellent corrosion resistance;
Lower manufacturing costs;
More economical operation and maintenance.
At present, the development of simulation technologies and engineering software is also becoming an important research direction. These technologies can provide effective guidance for fouling prediction, cleaning cycle optimization, and operational performance evaluation.






